Buying Guide

Zebra HC100 Wristband Printer: Specs, Cartridges and Buying Guide

Sarah Jane Nov 16, 2026 5 min read
Zebra HC100 Wristband Printer: Specs, Cartridges and Buying Guide

The Zebra HC100 wristband printer is a compact direct thermal printer built around one job: printing patient and visitor wristbands from a drop-in cartridge. This guide covers the HC100 units in our listing, what the store data says about each one, how the cartridge system works, and what to check before you buy a refurbished unit. Jump straight to the HC100 specs table if you only need the numbers.

Zebra has discontinued the HC100 and ended its own service and support, yet many sites still run it because the workflow is simple and staff already know it. If you are keeping a fleet going, adding a spare for a ward or registration desk, or weighing a move to a newer model, the sections below explain the choices in plain terms for single unit and multi unit buyers alike.

Products in our listing

We currently list two refurbished Zebra HC100 configurations.

Both units are refurbished, per their condition tags, and each comes with the 30-Day Tech Seller USA warranty. A manufacturer warranty is not guaranteed.

Need HC100 units for several desks?

Tell us how many printers and which interfaces you need and we will put a quote together.

Request a Quote

Zebra HC100 specs from our listings

The table below uses the spec data stored on each product. Where a listing does not record a value we show Not listed rather than filling the gap from another unit.

Spec HC1GA-3001-0200 HC100-3001-1100
Product type Wristband printer Desktop label printer (wristband)
Condition Refurbished Refurbished
Print method Direct thermal (per title) Direct thermal
Resolution 300 dpi (12 dots/mm) 300 dpi
Print speed 2 in/sec (51 mm/sec) Not listed
Print width 0.75 in, 1 in or 1.1875 in wristband widths Not listed
Media Z-Band wristband cartridges Not listed
Interface RS-232 serial (DB-9), USB 2.0 Not listed
Wireless 802.11b/g wireless print server (factory option on this configuration) Not listed
Memory 8 MB flash, 16 MB SDRAM Not listed
Programming Not listed ZPL, ZPL II
Power 100 to 240 V AC, 50 to 60 Hz, 70 W external supply Not listed
Dimensions 5 x 7 x 9.5 in (W x H x D) Not listed
Weight 3.1 lbs 6.1 lbs
Warranty 30-Day Tech Seller USA 30-Day Tech Seller USA

The HC1GA-3001-0200 record is far more complete than the HC100-3001-1100 record. Treat the blanks on the older listing as unknown, not as missing hardware, and ask us to confirm any detail that matters to your install. The 6.1 lbs weight on HC100-3001-1100 is higher than the 3.1 lb Zebra lists in its HC100 user guide, so it may reflect packed weight.

What the Zebra HC100 wristband printer is for

The Zebra HC100 wristband printer exists to make wristband printing hard to get wrong. Instead of threading a roll of bands and a liner through a printer, the operator drops a sealed cartridge into the top of the unit and presses it down until it clicks. Zebra's user guide notes that print speed is set by the media cartridge, which keeps operator settings to a minimum. That design is why the HC100 became common at admission, registration and emergency desks where staff turnover is high and printing a band is only one small step in a busy process.

Because the cartridge carries the media, a site can keep adult, pediatric and infant cartridges on a shelf and swap between them in seconds. Zebra lists both adhesive closure and clip closure band styles, and the size is marked on the top of each cartridge so staff can grab the right one. Our healthcare label and wristband hardware guide explains where wristband printers sit alongside specimen and pharmacy label printers, and the Zebra healthcare label printers guide covers how to specify the wider Zebra healthcare range.

This guide does not make claims about the plastics, cleaning chemicals or regulatory status of the HC100 or its bands. If your organization has written requirements for patient care equipment, review Zebra's own documentation with your clinical engineering, infection prevention and IT teams before deployment. We cannot promise that any printer meets a specific hospital's requirements.

Who the HC100 suits

The Zebra HC100 wristband printer is a good fit when you already run HC100 printers and want a matching spare, when your band templates and print workflow are built around the HC100, or when you need a low cost way to add another registration point without retraining staff. Like for like replacement avoids touching the application that sends the band, which is often the hardest part of any change in a clinical setting.

It suits smaller sites as well as larger groups. A single clinic might want one spare unit on the shelf so a failed printer never stops admissions. A larger group might standardize on a set number of HC100 units per desk while it plans a longer move to a current model. Both approaches work, and we quote single units and multi unit orders in the same way.

It is less suited to buyers starting from scratch who need long term manufacturer support. Zebra ended service and support for the HC100 in North America on November 30, 2021, so new deployments should weigh that against the convenience of the cartridge workflow.

Key configuration choices

Resolution. Every HC100 in our listing is 300 dpi. That is the fixed printhead resolution Zebra gives for the model, and it is a good match for small barcodes and readable patient text on a narrow band. Our 203 vs 300 vs 600 dpi guide explains why 300 dpi matters on narrow media.

Print method. The HC100 is direct thermal only. There is no ribbon path, so running costs come down to cartridges alone. The direct thermal vs thermal transfer guide covers how direct thermal output behaves over time and why it suits short stay items such as wristbands.

Interfaces. Zebra lists RS-232 serial and USB 2.0 as standard, with 10/100 wired Ethernet and 802.11b/g wireless as factory installed options. Our HC1GA-3001-0200 listing records serial (DB-9) and USB 2.0, and its connectivity field describes an 802.11b/g wireless print server as a factory option on this configuration. Because that field is not definitive, confirm the configuration label on the unit before you plan a wireless rollout. Our printer connectivity guide walks through choosing between USB, serial, Ethernet and Wi-Fi.

Memory. The HC1GA-3001-0200 listing records 8 MB flash and 16 MB SDRAM, which matches the standard memory Zebra gives in the user guide. Zebra also lists an optional 64 MB flash, which is not recorded on either of our units.

HC100 wristband cartridges and media

Media is the biggest running cost on any wristband printer, so it is worth understanding the cartridge system before you commit. HC100 cartridges hold Zebra Z-Band wristbands. The user guide lists Z-Band Direct (adhesive closure) bands in 11 in, 7 in and 6 in lengths and Z-Band QuickClip bands in 11 in and 7 in lengths, covering adult, pediatric and infant sizes. Several band colors are available, which some sites use for alerts or departments.

Our HC1GA-3001-0200 listing records wristband widths of 0.75 in, 1 in and 1.1875 in. Zebra's user guide does not state widths, so check the cartridge part number against your band template before ordering media in volume. Zebra also notes that print speed is set by the cartridge, at either 2 or 4 inches per second.

A few practical media tips:

  • Keep cartridges sealed until use and store them away from heat and direct sunlight, as with any direct thermal stock.
  • Match your template to the band size printed on the cartridge so text and barcodes stay inside the printable area.
  • Keep a mix of sizes at each desk so staff never print an adult band for an infant because the right cartridge ran out.

Our label media and ribbon selection guide covers wider media choices, and the barcode symbologies guide helps when choosing a barcode type that fits on a narrow band.

Setup, drivers and command language

Zebra lists ZPL II and XML as standard on the HC100, with ZBI 2.0 as an option. Our HC100-3001-1100 listing records ZPL and ZPL II. In practice that means most hospital information systems and wristband applications that already print to Zebra devices can drive the HC100 with existing ZPL templates. The ZPL vs ESC/POS guide explains why ZPL is the default for label and wristband work.

Setup steps for a replacement unit are usually short:

  1. Connect power from the external supply and the interface cable you plan to use.
  2. Load a cartridge by pressing it down until it clicks, leaving about 6 in of clearance above the printer as Zebra advises.
  3. Install the Zebra driver or point your application at the printer, then print a test band.
  4. Check the barcode scans at the bedside with the scanners your staff actually use.

If a band prints faintly or skips, our label printer troubleshooting guide covers the usual checks before you suspect the hardware.

Lifecycle and replacement options

Zebra's HC100 support page states that the product is discontinued. It lists a North America printer discontinuation date of October 31, 2018 and a North America service and support discontinuation date of November 30, 2021. The page keeps its support resources available but says they will no longer be updated. Zebra does not name a replacement model on that page.

For many sites the practical answer is a mix: keep the HC100 fleet running with refurbished spares while testing a current model on one or two desks. In our listing the closest comparison is the Zebra ZD510-HC wristband printer (ZD51013-D01E00FZ), also a 300 dpi direct thermal wristband printer. The table sets out HC100 vs ZD510-HC from our listings.

Feature Zebra HC100 (our listings) Zebra ZD510-HC (ZD51013-D01E00FZ)
Print method Direct thermal Direct thermal
Resolution 300 dpi 300 dpi
Connectivity in store data Serial and USB on HC1GA-3001-0200 USB, Ethernet, Bluetooth
Programming in store data ZPL, ZPL II on HC100-3001-1100 ZPL, ZPL II
Weight in store data 3.1 lbs and 6.1 lbs 3.1 lbs
Zebra status Discontinued, support ended Check Zebra for current status

Before switching, confirm that your wristband application has a driver or template for the new model and that the band media you plan to buy is listed for it. The Zebra ZD series guide explains how current Zebra desktop models are named, and the Zebra legacy desktop printers guide covers keeping older Zebra fleets running.

Refurbished HC100 checklist

A refurbished HC100 is a sensible way to add capacity or keep spares, as long as you check the right things on arrival. Our refurbished grading guide explains how we describe condition. For the HC100 in particular:

  • Print quality. Print a full test band and look for white lines or faint areas, which point to printhead wear. The printhead diagnosis guide explains what to look for.
  • Cartridge seating. Load and remove a cartridge several times. It should click into place and be recognized every time.
  • Interfaces. Confirm the ports on the back match the configuration you ordered, especially if you need wired or wireless networking.
  • Power supply. Make sure the external supply is included and rated 100 to 240 V AC.
  • Firmware and settings. Print a configuration report so you know the firmware level and network settings before the unit goes live.
  • Cleaning. Follow Zebra's cleaning instructions in the user guide and our thermal printer maintenance guide to keep the printhead clear of debris.

Returns, if needed, follow our 30 day policy with a 25% restocking fee that is waived for defective or wrongly shipped items. Orders ship with FedEx or DHL.

Full HC100 range in our listing

Part number Listing Condition Key store specs
HC1GA-3001-0200 Zebra HC100 Direct Thermal Wristband Printer Refurbished 300 dpi, serial and USB, Z-Band cartridges
HC100-3001-1100 Zebra HC100 Wristband 300dpi Direct Thermal Desktop Label Printer Refurbished 300 dpi direct thermal, ZPL

You can also browse every Zebra printer on the Zebra printers collection or the full printers collection.

Planning a wristband printer refresh?

Ask for a quote on HC100 spares or a mix of HC100 and newer Zebra models.

Request a Quote

Common questions

Is the Zebra HC100 still supported by Zebra?

Zebra lists the HC100 as discontinued. Its support page gives a North America printer discontinuation date of October 31, 2018 and a service and support discontinuation date of November 30, 2021, so plan on independent service and spare parts rather than Zebra support.

What media does the HC100 wristband printer use?

The HC100 loads Zebra Z-Band wristband cartridges. Zebra describes adult, pediatric and infant sizes marked on the top of each cartridge, in both adhesive closure and clip closure styles.

Does the Zebra HC100 need a ribbon?

No. The HC100 is a direct thermal printer with a 300 dpi printhead, so it prints straight onto heat sensitive wristband stock and there is no ribbon to buy or load.

How fast does the HC100 print a wristband?

Zebra states a print speed of 2 or 4 inches per second, set by the media cartridge. Our HC1GA-3001-0200 listing records 2 inches per second.

Which interfaces does the HC100 have?

Zebra lists RS-232 serial and USB 2.0 as standard, with wired Ethernet and 802.11b/g wireless as factory installed options. Check the configuration label on the unit you buy before planning a network install.

Is there a Zebra HC100 replacement?

Zebra does not name a replacement on its HC100 support page. The Zebra ZD510-HC is a 300 dpi direct thermal wristband printer in our listing and is the natural model to compare when planning a newer platform.

Ready to add HC100 printers?

Request a quote for one unit or a full set of desks.

Request a Quote
Sarah Jane

Sarah Jane

Senior IT Hardware Specialist · Tech Seller USA
Sarah helps businesses and IT teams source the right enterprise hardware at wholesale prices. View profile