Zebra GX430t Label Printer: 300 dpi Specs and Buying Guide
The Zebra GX430t label printer is a 4 inch, 300 dpi desktop printer that prints by thermal transfer or direct thermal, built for small, sharp labels on a bench, at a packing station or in a lab. It has been a standard Zebra desktop model for years, which is why so many sites still run it and need matching units.
We list nine GX430t part numbers, all refurbished, in three interface builds: USB with serial and Ethernet, USB with serial and parallel, and USB with serial and Wi-Fi. This guide covers what the GX430t is for, who it suits, how to choose a build, media and ribbon, setup and command languages, its lifecycle status at Zebra and the replacement Zebra names, what to check on a refurbished unit, and how it compares with the GX420t and ZD621t. For recorded values, jump to the GX430t specs table or the full GX430t range.
In this guide
Products in our listing
Four GX430t builds are shown below; the full range table lists all nine part numbers.
Every Zebra GX430t label printer we list is refurbished and carries the 30-Day Tech Seller USA warranty. Browse the full Zebra printer range or all printers and scanners.
Matching one GX430t or a whole bench?
Send the part numbers and quantities you need and we will confirm each build and quote.
Zebra GX430t specs in our listing
Values below come from our product data. GX43-102410-00GA has its own column because its record differs from the other eight; where a value is not recorded it is shown as Not listed.
| Specification | GX43-102410-00GA | Other eight GX430t part numbers |
|---|---|---|
| Condition | Refurbished | Refurbished |
| Print method | Thermal transfer / direct thermal | Thermal transfer / direct thermal |
| Resolution | 300 dpi | 300 dpi |
| Print speed | 4 in/sec | Up to 4 in/sec (102 mm/s) |
| Max print width | 4 inches | 4.09 inches (104 mm) |
| Media width | Not listed | 0.75 inches to 4.25 inches |
| Memory | Not listed | 4MB Flash / 8MB SDRAM |
| Command languages | Not listed | ZPL II, EPL2 |
| Connectivity | USB, Serial, Ethernet | USB, Serial and one of Ethernet, Parallel or Wi-Fi (see range table) |
| Listed weight | 4.6 lbs | 4.6 lbs |
| Warranty | 30-Day Tech Seller USA | 30-Day Tech Seller USA |
What the Zebra GX430t label printer is for
The Zebra GX430t label printer is built for labels where detail matters more than raw speed. At 300 dpi it prints small text, small 2D codes and fine barcodes cleanly, so it is common on product and shelf labels, specimen and sample labels, small parts and electronics labels, jewelry and retail tags, and pharmacy and dispensing labels. It also handles everyday 4 inch shipping labels, although a 203 dpi printer does that job faster.
Because it prints both thermal transfer and direct thermal, one GX430t can produce long-life ribbon printed labels for assets and products, and short-life direct thermal labels for shipping, without changing printers. Our direct thermal vs thermal transfer guide explains which labels need a ribbon, and the Zebra G-Series GC vs GK vs GX guide shows where the GX430t sits among the other G-Series models.
Who the GX430t suits
The Zebra GX430t label printer suits buyers who already run GX430t printers and want identical replacements or extra units. Matching the existing model keeps label templates, driver settings, ribbon and media sizes and operator habits the same, so a new unit goes into service with almost no setup. That is especially valuable on validated processes in labs, pharmacies and regulated production, where changing printer models can mean revalidating every label.
It also suits multi-unit buyers on a budget who need 300 dpi output at many stations, and single-unit buyers replacing one failed printer. For very high daily volumes, an industrial printer is a better fit; our industrial vs desktop label printers guide explains where that line falls.
Choosing the right GX430t build
Interface. This is the main difference between our nine part numbers. Four are recorded with USB, serial and Ethernet, which suits shared network printing from a warehouse, ERP or lab system. Four are recorded with USB, serial and parallel, which suits a single workstation or older equipment that still uses a parallel or serial port. One, GX43-102710-000, is recorded with USB, serial and Wi-Fi for stations where running a network cable is impractical. Our printer connectivity guide covers each option.
Match the part number. When you replace a unit, read the full part number from the label on the printer you are replacing and match it, rather than ordering by model name. The suffix differences between our part numbers reflect different factory configurations, and our data records the interface for each one in the range table below.
Resolution. Every GX430t is 300 dpi. If your labels are large and simple, the 203 dpi GX420t prints them faster. Our 203 vs 300 vs 600 dpi resolution guide explains the trade off.
Media and ribbon for the GX430t
Our data records a media width of 0.75 to 4.25 inches and a maximum print width of 4.09 inches (104 mm) for the GX430t, with GX43-102410-00GA recorded at a 4 inch print width. That covers small 1 inch labels up to standard 4 x 6 shipping labels.
For thermal transfer, match the ribbon width to the label, or slightly wider, and match the ribbon type to the material: wax for paper labels, wax and resin for coated paper and many synthetics, and resin for polyester and polypropylene labels that need to resist chemicals, heat or abrasion. Use ribbons made for Zebra desktop printers so the core and winding match. Our label media and ribbon selection guide goes into detail, and if you see creases in the print, the ribbon wrinkle diagnosis guide explains the usual causes.
Setup, command languages and compatibility
Our data records ZPL II and EPL2 for the GX430t. ZPL II is the language most modern label software, shipping platforms and warehouse systems send to Zebra printers. EPL2 is the older Zebra desktop language, and support for it means a site still sending EPL from older software can keep running without rewriting its label formats. Our ZPL vs ESC/POS command languages guide explains the differences.
The recorded memory is 4MB Flash and 8MB SDRAM. That is plenty when your software sends a complete label each time, but it is limited if you store many formats, fonts or graphics on the printer, so check your stored content before standardizing.
A practical GX430t driver setup sequence: load media and ribbon, run media calibration, print a configuration label, set the network address on Ethernet or Wi-Fi builds, install the printer driver, then print your real labels from your own application. Zebra support shows Zebra Setup Utilities for configuring the printer on Windows. On a 300 dpi printer, make sure your label templates are set for 300 dpi; a template built for 203 dpi will print smaller than expected.
GX430t lifecycle and replacement
Zebra lists the GX430t as discontinued. Its support page states that Zebra is no longer offering the product for sale, with a printer discontinuation date of January 31, 2022 and a service and support discontinuation date of April 30, 2025 for North America, EMEA and Latin America. Zebra names the ZD621 as the official Zebra GX430t replacement.
What this means for buyers: Zebra no longer sells new GX430t printers or provides customer support for them, so refurbished units are the practical way to keep an existing GX430t fleet consistent. For a new deployment, or a site planning several years ahead, the ZD621 is the model Zebra points to. Our Zebra ZD Series desktop printers guide and ZD620 vs ZD621 part number guide explain the newer range, and our guide to legacy Zebra desktop printers covers the older models many GX430t units replaced.
Buying a refurbished GX430t: what to check
Printhead. At 300 dpi each heating element is small, so a single failed dot shows as a white line through text or a barcode. Print a test pattern on arrival. Our printhead failure diagnosis and replacement guide explains what to look for.
Platen roller. A worn, glazed or sticky platen causes skew and light print that is often mistaken for a head fault. Our thermal printer maintenance guide covers cleaning.
Interface and box contents. Confirm the build matches your part number, that the interface you need works, and that the power supply and cord are present.
Condition terms. Our refurbished hardware grading guide explains what refurbished means at Tech Seller USA.
GX430t vs GX420t and ZD621t in our listing
The Zebra GX420t (GX42-102410-000) is the 203 dpi model in the same chassis. Our data records it at up to 6 in/sec (152 mm/s), with the same 4.09 inch print width, 0.75 to 4.25 inch media width, 4MB Flash and 8MB SDRAM, ZPL II and EPL2, USB, serial and Ethernet, and 4.6 lbs. Choose the GX420t for faster shipping and carton labels, and the GX430t when small text or small codes need 300 dpi.
The Zebra ZD621t (ZD6A043-301F00EZ) is a 300 dpi model in the range Zebra names as the GX430t replacement. Our data records it as thermal transfer at up to 6 in/sec (152 mm/s), a 4 inch print width, 0.585 to 4.65 inch media width, 512MB Flash and 256MB SDRAM, ZPL II and EPL2, USB, Ethernet and serial, and 5.5 lbs. It is faster at 300 dpi and has far more memory than the GX430t, so it suits sites that store many formats on the printer or want a model Zebra still supports.
Full GX430t range in our listing
Every GX430t part number we list is below. All are 300 dpi, thermal transfer and direct thermal, and refurbished. Select a part number to open its product page.
| Part number | Interface | Resolution | Print method | Speed | Condition |
|---|---|---|---|---|---|
| GX43-102410-00GA | USB / Serial / Ethernet | 300 dpi | Thermal transfer / direct thermal | 4 in/sec | Refurbished |
| GX43-100410-000 | USB / Serial / Ethernet | 300 dpi | Thermal transfer / direct thermal | Up to 4 in/sec | Refurbished |
| GX43-102410-000 | USB / Serial / Ethernet | 300 dpi | Thermal transfer / direct thermal | Up to 4 in/sec | Refurbished |
| GX43-102420-000 | USB / Serial / Ethernet | 300 dpi | Thermal transfer / direct thermal | Up to 4 in/sec | Refurbished |
| GX43-100310-000 | USB / Serial / Parallel | 300 dpi | Thermal transfer / direct thermal | Up to 4 in/sec | Refurbished |
| GX43-102510-000 | USB / Serial / Parallel | 300 dpi | Thermal transfer / direct thermal | Up to 4 in/sec | Refurbished |
| GX43-102510-00GA | USB / Serial / Parallel | 300 dpi | Thermal transfer / direct thermal | Up to 4 in/sec | Refurbished |
| GX43-102512-000 | USB / Serial / Parallel | 300 dpi | Thermal transfer / direct thermal | Up to 4 in/sec | Refurbished |
| GX43-102710-000 | USB / Serial / Wi-Fi | 300 dpi | Thermal transfer / direct thermal | Up to 4 in/sec | Refurbished |
Found your GX430t part number?
Request a quote for one printer or several, and list every part number and quantity you need.
Common questions
Is the Zebra GX430t discontinued?
Yes. Zebra lists the GX430t as discontinued, with a printer discontinuation date of January 31, 2022 and a service and support discontinuation date of April 30, 2025 for North America, EMEA and Latin America.
What replaced the Zebra GX430t?
Zebra names the ZD621 as the replacement for the GX430t. We list the ZD621t in 300 dpi alongside refurbished GX430t printers for sites that want to match an existing fleet.
What is the difference between the GX430t and GX420t?
The GX430t is 300 dpi and recorded at up to 4 in/sec, while the GX420t is 203 dpi and recorded at up to 6 in/sec. Both are 4 inch thermal transfer and direct thermal desktop printers with ZPL II and EPL2 in our data.
Does the GX430t print direct thermal labels?
Yes. Every GX430t in our listing is recorded as thermal transfer and direct thermal, so it prints with a ribbon for durable labels or without one on direct thermal media.
Which GX430t interface build should I buy?
Match the part number of the unit you are replacing. For a new station, choose the Ethernet build for shared network printing, the parallel build for a single workstation or older equipment, or the Wi-Fi build where cabling is impractical.
What warranty comes with a GX430t from Tech Seller USA?
Every GX430t we sell carries the 30-Day Tech Seller USA warranty. Manufacturer warranty is not guaranteed.
Ready to order a GX430t?
Send the part number you are replacing, your label size and how many units you need, and we will confirm the build before quoting.




