TSC TTP-247 Label Printer: 4 Inch Specs and Buying Guide
The TSC TTP-247 label printer is a 4 inch desktop barcode printer that runs thermal transfer with a ribbon or direct thermal without one, built for the steady middle ground between a light office printer and an industrial floor model. TSC states it prints up to 7 inches per second at 203 dpi and takes a full 300 m ribbon, which makes it a regular choice for shipping desks, small warehouses, manufacturing cells and retail back rooms that print hundreds of labels a day.
This guide covers the TTP-247 part number in our listing, what TSC states about the platform, which ribbon and media it takes, how it compares with the TTP-345 and other TSC desktops we list, and what to check on a refurbished unit whether you need one printer or several. For the numbers only, go straight to the TTP-247 specs table.
In this guide
- Products in our listing
- TSC TTP-247 specs in our listing
- What the TSC TTP-247 label printer is built for
- Who the TTP-247 suits
- TTP-247 ribbon size and media
- Connectivity, command language and setup
- TTP-247 vs TTP-345 and other TSC printers we list
- Buying a refurbished TTP-247: what to check
- Ordering
- Common questions
Products in our listing
The TTP-247 part number we list is below. The card opens the product page, and the part number on the card is the one to quote when you order.
This TTP-247 is refurbished. It carries the 30-Day Tech Seller USA warranty; manufacturer warranty is not guaranteed. Browse the full TSC printer range.
Need one TTP-247 or a set for several stations?
Send the part number and quantity and we will confirm the configuration and quote.
TSC TTP-247 specs in our listing
Values below come from our product page for part 99-125A013-5061. Where our listing does not record a value, it shows as not listed.
| Spec | 99-125A013-5061 |
|---|---|
| Condition | Refurbished |
| Print method | Thermal transfer / direct thermal |
| Resolution | 203 dpi |
| Max print width | 4.25 in (108 mm) |
| Print speed | Up to 7 in/sec |
| Interfaces | USB, Serial, Parallel, Ethernet |
| Memory | 4 MB flash, 8 MB SDRAM |
| Display | Not listed |
| Dimensions | 8.4 in W x 7.4 in H x 12.4 in D |
| Power | 100-240 V AC |
| Listed weight | 6.17 lbs |
| Warranty | 30-Day Tech Seller USA |
These values line up with what TSC publishes for the TTP-247: 203 dpi, up to 7 ips, a 108 mm (4.25 in) maximum print width, 8 MB SDRAM and 4 MB flash, and a footprint of 8.39 by 7.40 by 12.36 inches. TSC adds an SD card reader for flash expansion up to 4 GB, which is useful for stored fonts, logos and label formats.
What the TSC TTP-247 label printer is built for
TSC places the TTP-247 in its TTP series of 4 inch performance desktop printers and names the TTP-245 Plus as its predecessor. The design goal is a desktop that behaves more like a light industrial printer: a double walled plastic clamshell, a 32-bit RISC processor, a full length 300 m ribbon and an optional external roll mount for large label rolls. TSC lists a maximum print length of up to 90 inches, a minimum label length of 10 mm, and sensors for gap, black mark, head open and ribbon end.
The 7 ips top speed is the headline. At 203 dpi it is fast for a desktop and suits batch runs of shipping, carton and product labels. Resolution is the trade off: 203 dpi handles standard linear barcodes, addresses and most product labels well, but for very small text and dense 2D codes a 300 dpi model is the safer choice. Our resolution guide sets out where that line falls.
Who the TTP-247 suits
- Shipping and fulfillment desks: 4 by 6 inch carrier labels and packing labels in steady daily volume.
- Small warehouses: carton, bin and location labels, with thermal transfer for labels that must last.
- Manufacturing cells: product, serial and compliance labels printed at the line.
- Retail back rooms: price tickets, tags and shelf labels in batches.
- Offices and labs: asset tags and sample labels where a durable thermal transfer print is needed.
If you print thousands of labels per shift, an industrial printer with a metal frame and larger ribbon capacity will last longer under that load than a 4 inch thermal transfer desktop printer. Our industrial versus desktop guide and duty cycle and print volume guide help you size the printer to the work.
TTP-247 ribbon size and media
Ribbon capacity is one of the main reasons buyers pick the TSC TTP-247 label printer over smaller desktops. TSC lists ribbons up to 300 m (984 ft) long on a 1 inch core. Longer ribbons mean fewer changes and a lower cost per label than the short ribbons many compact desktops take. Choose a ribbon at least as wide as the label so the printhead never runs on bare liner, and match the ribbon to the label face: wax for paper, wax resin for coated paper and many synthetics, resin for polyester and polypropylene that must resist chemicals and abrasion.
For labels, TSC lists media from 20 to 112 mm (0.78 to 4.4 in) wide and 0.06 to 0.19 mm thick, wound outside, on cores from 1 to 3 inches. The internal roll capacity is 127 mm (5 in) outside diameter, and the optional external roll mount takes rolls up to 214 mm (8.4 in) on a 1 or 3 inch core. TSC lists continuous, die cut, black mark, fan fold and notched media, and a label spindle for 3 inch cores as an option. If your supplier ships industrial rolls on 3 inch cores, plan for that spindle and the external mount.
TSC lists a peel off module and a guillotine cutter as options, with peel mode at 2 to 3 ips and label lengths from 1 to 6 inches in peel mode. Our label media and ribbon selection guide and media handling modes guide cover each choice, and our guide to direct thermal versus thermal transfer explains when the ribbon earns its cost.
Connectivity, command language and setup
TSC lists USB 2.0, Centronics parallel and RS-232 serial as standard on the TTP-247, with Ethernet and a Bluetooth module as options. The part number in our listing records USB, serial, parallel and Ethernet, so it can sit on a network as a shared printer or connect straight to one PC. The parallel port is useful when the printer replaces an older unit on legacy equipment that only speaks parallel. Our printer connectivity guide explains when each port makes sense.
For software, TSC lists TSPL-EZ as the printer language with TPLE and TPLZ translation languages, which cover Eltron EPL and Zebra ZPL formats. That lets many label formats built for other brands run without a rewrite. Emulation covers common commands rather than every feature, so send your real formats to one printer before a wider rollout. Our guide to ZPL versus ESC/POS explains how printer languages differ.
For first setup and TTP-247 calibration, load media and ribbon, set the sensor for gap or black mark stock, run the media calibration from the TSC Diagnostic Tool or the driver, then set darkness and speed. Running at full 7 ips can lighten the print on some ribbon and label pairs, so if barcodes scan poorly, drop the speed a step before you raise darkness. Our print darkness and speed tuning guide walks through that process.
TTP-247 vs TTP-345 and other TSC printers we list
| Model in our listing | Resolution | Max print width | Listed speed | Listed interfaces | Condition |
|---|---|---|---|---|---|
| TTP-247 (99-125A013-5061) | 203 dpi | 4.25 in | Up to 7 in/sec | USB, Serial, Parallel, Ethernet | Refurbished |
| TTP-244CE (99-033A031-0001) | 203 dpi | 4 in | Not listed | USB, Serial, Parallel, Ethernet | Refurbished |
| TC210 (99-059A001-1201) | 203 dpi | 4 in | Up to 6 ips | USB, Serial, Ethernet, Wi-Fi, Bluetooth | New |
| TC310 (99-059A002-2001) | 300 dpi | 4.15 in | 4 ips | USB, Serial, Ethernet, USB Host | Refurbished |
| TX200 (99-053A033-0201) | 203 dpi | 4.25 in | Up to 8 ips | USB, USB Host, Serial, Ethernet | New |
| TTP-225 (99-040A010-0301) | 203 dpi | 2 in | 5 ips | USB, Serial, Ethernet | New |
TTP-247 versus TTP-345. TSC sells these two as one series with the same memory and options. The TTP-247 prints at 203 dpi and up to 7 ips; the TTP-345 prints at 300 dpi and up to 5 ips. Pick the TTP-345 for small text, small labels and dense 2D codes, and the TTP-247 for speed on standard labels. Our TSC TTP-345 guide covers that model in detail.
Other options. The TC210 is another 4 inch TSC desktop; the unit we list records Wi-Fi and Bluetooth alongside USB, serial and Ethernet, at up to 6 ips. The TC310 is the 300 dpi choice with far more memory recorded in our listing. The TX200 records up to 8 ips and 128 MB of RAM and flash for heavier work. TSC also offers the TDP-247, a direct thermal only sibling for sites that never use ribbon. If your labels are 2 inches or narrower, the TTP-225 saves space and consumables. Our TSC label printers range guide explains how the families fit together.
Buying a refurbished TTP-247: what to check
Printhead. Print a full width test pattern and look for white lines running the length of the label, which mean failed dots. A worn head on a 203 dpi printer shows first in barcodes, so scan a test barcode as well as looking at it. Our printhead failure guide covers diagnosis and replacement.
Ribbon path. Run a full ribbon width print and check for creases or smearing. Creases usually point to ribbon tension or head pressure settings rather than a fault, and our ribbon wrinkle diagnosis guide shows how to fix them.
Platen, sensors and ports. Look at the platen roller for flat spots, clean the gap and black mark sensors, and confirm every port you plan to use works, including the Ethernet link. Set a cleaning routine from day one; our thermal printer maintenance guide has a schedule, and the refurbished hardware grading guide explains what our condition descriptions cover.
Ordering
Tell us how many printers you need, your label width and roll size, the ribbon type you use or plan to use, and how each printer will connect. We will confirm the TSC TTP-247 label printer configuration fits and quote for one unit or several stations. You can also browse all printers.
Found the TTP-247 you need?
Request a quote for one printer or several, and tell us your label and ribbon sizes so we can confirm the fit.
Common questions
Is the TSC TTP-247 thermal transfer or direct thermal?
Both. Our TTP-247 listing records thermal transfer and direct thermal, and TSC lists both print methods for the TTP-247. Load a ribbon for labels that must last, or run direct thermal stock with no ribbon for shipping and other short life labels.
What ribbon size does the TSC TTP-247 take?
TSC lists ribbons up to 300 m (984 ft) long on a 1 inch core. Choose a ribbon at least as wide as your label so the liner edges stay clean, and match the ribbon type to the label face: wax, wax resin or resin.
What is the difference between the TTP-247 and the TTP-345?
TSC sells them as one series. The TTP-247 prints at 203 dpi and up to 7 ips, while the TTP-345 prints at 300 dpi and up to 5 ips. Both list 8 MB SDRAM and 4 MB flash with an SD card reader. Choose the TTP-345 for small text and dense 2D codes.
How big a label roll fits the TTP-247?
TSC lists an internal label roll capacity of 5 inches outside diameter, and up to 8.4 inches with the optional external roll mount, on cores from 1 to 3 inches. Media width runs from 0.78 to 4.4 inches.
Can the TTP-247 print ZPL or EPL label formats?
TSC lists TSPL-EZ as the printer language, with TPLE and TPLZ translation languages for Eltron EPL and Zebra ZPL formats. Test your real formats on one unit before a rollout, because emulation covers common commands rather than every feature.
How do I calibrate the TTP-247 for a new label?
Load the media, set the sensor for gap or black mark labels, then run the media calibration from the TSC Diagnostic Tool or the printer driver so the printer learns the label length. Run it again whenever you change label stock.
Ready to order a TSC TTP-247?
Send your quantity and how the printers will connect, and we will confirm the configuration before quoting.

