XS3840SE70045 Seagate Nytro 3.84TB SAS SSD: When SAS Flash Fits
The XS3840SE70045 is a Seagate Nytro 3.84TB SAS enterprise SSD, and buyers reach for it when they want flash on a SAS backplane rather than NVMe. This covers what it is, where SAS SSDs still make sense, and what to confirm before buying.
What is the Seagate XS3840SE70045?
A 2.5 inch, 3.84TB, SAS 12Gb/s enterprise solid state drive from the Seagate Nytro 3000 family. The XS prefix identifies Nytro SAS SSDs; the capacity and suffix identify the variant.
Nytro SAS SSDs ship in several endurance classes under adjacent part numbers. Confirm the endurance rating (DWPD) on the datasheet for this exact part before assuming it suits a write-heavy workload. Our endurance guide covers what DWPD means for drive life.
Why choose a SAS SSD instead of NVMe?
Three reasons, and they are about the platform rather than the drive.
The server has SAS bays and no NVMe bays. Most servers of the Gen9/Gen10 and 13th/14th generation era have SAS/SATA backplanes. A SAS SSD is the way to put flash in those bays. Our ProLiant compatibility guide and PowerEdge guide cover which bays support what.
Hardware RAID on the existing controller. A SAS SSD sits behind the RAID controller like any SAS drive, so redundancy comes from the controller. NVMe on older platforms bypasses the controller entirely.
Dual-port for multipath. SAS SSDs have two ports; most NVMe drives of this era do not. Our dual-port guide covers when that matters.
Where NVMe wins: raw throughput and latency on a platform that supports it. A SAS SSD is limited by the 12Gb/s link; NVMe is not. Our interface guide covers the comparison.
SAS SSD vs SATA SSD
Both go in the same 2.5 inch bays on most backplanes. The differences: SAS has dual ports, a faster link, and better command queuing. SATA is cheaper. For a single-controller server doing general work, an enterprise SATA SSD is frequently sufficient. Our PM883 guide covers a SATA alternative.
What to check before buying
Five things.
SAS controller that handles SSDs properly. Older controllers cap flash performance in ways that waste the drive. Our controller guide covers checking.
Endurance class matches the workload, per above.
Firmware coding. Behind a Smart Array or PERC, a bare Seagate may be flagged; the vendor-coded 3.84TB SAS SSD is safer. Our HPE SSD guide covers what non-coded drives do on Smart Array.
Carrier, generation-matched.
If used, remaining endurance. A used SSD with most of its rated writes consumed is not a bargain. Our burn-in guide covers what to ask.
Frequently asked questions
What is the XS3840SE70045?
A Seagate Nytro 3.84TB SAS 12Gb/s enterprise SSD in 2.5 inch form factor. Confirm the endurance class on the datasheet for this exact part.
Why buy a SAS SSD instead of NVMe?
When the server has SAS bays and no NVMe bays, when you want hardware RAID on the existing controller, or when dual-port multipath is needed. NVMe wins on raw performance where the platform supports it.
Will a SAS SSD work in a SATA bay?
No. A SAS drive requires a SAS controller and backplane. SATA SSDs work in SAS bays, but not the reverse.
Does my RAID controller handle SSDs properly?
Older controllers cap flash performance. Check the controller specification and firmware before spending on SAS SSDs, or the drive will be limited by the controller rather than its own capability.
Will it work in an HPE or Dell server?
Behind an HBA, yes. Behind a Smart Array or PERC that validates firmware, a bare Seagate may be flagged; the vendor-coded 3.84TB SAS SSD is safer. Needs the correct carrier.
What should I check on a used XS3840SE70045?
Remaining endurance as a percentage, media errors, and whether it was cryptographically erased. A used SSD with most of its rated writes consumed is not a bargain.
Seagate Nytro SAS SSD
XS3840SE70045 3.84TB SAS 12Gb/s Enterprise SSD
Tell us your controller and workload and we will confirm SSD support, endurance class and coding before you order.
View Details & Request a Quote →
